outcomes – WELCOME TO WWW.PLANESINTHEAIR.COM

JACKSONVILLE, Fla., Oct. 28, 2021 — Boeing [NYSE: BA] today broke ground to begin construction of a new 370,000 square-foot maintenance, repair and overhaul (MRO) facility located at Cecil Airport that, once complete, will support Boeing’s ability to deliver readiness outcomes for U.S. government customers.

The facility will include eight new hangars, additional work space and offices where Boeing maintainers, engineers and data analysts will support U.S. Navy and Air Force aircraft. The facility’s close proximity to Naval Air Station Jacksonville, Boeing’s Training Systems Center of Excellence in west Jacksonville, and local academic institutions make it a leading location for the development and delivery of innovative product support, underpinned by collaborative research and engineering.

The groundbreaking ceremony celebrates a 25-year lease agreement between Boeing and the Jacksonville Aviation Authority (JAA). Under the agreement, the JAA will construct and lease to Boeing new facilities on approximately 30 acres located on the northeast side of Cecil Airport, near Boeing’s existing MRO site. Construction is anticipated to be completed in 2023.

Since opening its existing MRO facilities at Cecil Airport in 1999, Boeing teammates have maintained, modified and upgraded 1,030 aircraft for the U.S. Navy and Marine Corps, including the F/A-18 A-D Hornet, F/A-18 E/F Super Hornet and EA-18G Growler. The Boeing team at the site also converts F/A-18 Super Hornets into flight demonstration aircraft for the U.S. Navy’s Blue Angel squadron as well as modifies retired F-16s into the next generation of autonomous aerial targets for the U.S. Air Force. The facility is also home to a Flight Control Repair Center that provides structural repairs to F/A-18 A-F and EA-18G flight control surfaces.

An Allegiant Air MD-83 passenger jet takes off from the Monterey airport

WASHINGTON (Reuters) – The U.S. Federal Aviation Administration (FAA) needs to improve its oversight to address maintenance issues at Allegiant Air, the 11th largest U.S. carrier, according to a report seen by Reuters on Tuesday.

The U.S. Transportation Department’s Inspector General, in a 31-page report sent to Capitol Hill on Tuesday but not yet made public, said FAA inspectors since 2011 have not “consistently documented risks associated with 36 Allegiant Air in-flight engine shutdowns for its MD-80 fleet or correctly assessed the root cause of maintenance issues.”

Ultra-low cost Allegiant, a unit of Allegiant Travel Co, said it had not yet see the report and did not have an immediate comment.

The FAA said in a letter attached to the report that it agreed with eight of the nine recommendations made by the inspector general and partially agreed with the remaining one.

Allegiant carried about 14 million passengers last year, serving 122 U.S. cities and Puerto Rico on 450 flight routes.

The inspector general opened the probe in May 2018 after a “series of in-flight engine shutdowns, aborted takeoffs, and unscheduled landings” raised concerns about maintenance practices.

The report said in-flight shutdowns at Allegiant “continued until July 2018 and were only resolved four months later when Allegiant Air retired the last of its MD-80 fleet.” Allegiant now flies an all Airbus fleet.

The report found in-flight engine shutdowns forced 21 Allegiant aircraft to return or divert to other airports between 2014 and 2018, but that regulators did not properly track engine shutdown risks.

A 2015 maintenance provider failure at Allegiant Air demonstrated “severe violations that represent unacceptable safety risks or could result in catastrophic outcomes should also warrant a more stringent oversight approach,” the report said.

The inspector general said the airline’s maintenance provider failed to insert a cotter pin on a critical flight control component that put some 30,000 passengers at risk.

The report said in August 2015, a pilot “almost lost control of this aircraft during takeoff when it unexpectedly tried to lift off prematurely” but was able to abort takeoff and land safely.

After inspectors proposed a 30-day suspension for Allegiant Air’s maintenance provider, FAA regional officials reduced the suspension to a compliance action. FAA inspectors closed out six of eight compliance actions before ensuring Allegiant Air actually took any corrective actions, the report found.

It also found that FAA does not provide inspectors with guidance and comprehensive training to ensure Allegiant Air takes appropriate corrective actions.

The FAA said it had “initiated compliance actions at Allegiant Air that have improved safety for the flying public.”

(Reporting by David Shepardson; Editing by Richard Chang and Bill Berkrot)

Tag: outcomes

Boeing Breaks Ground on New Maintenance, Repair & Overhaul Facility in Jacksonville

FAA Must Boost Oversight to Address Allegiant Air Maintenance Issues

Archives